Nordlift Oy designs and manufactures lifting systems to lift up rail vehicles: locomotives, complete trains, trams and metro cars. Our systems go into new production lines and into heavy maintenance depots, anywhere a heavy vehicle needs to come up smoothly and stop exactly where you want it.

On 22-25 September 2026, you will find us at InnoTrans in Berlin, the rail industry’s biggest event of the year. Come and talk to us about your lifting needs.

Meet us at InnoTrans 2026

Where: Messe Berlin, Berlin Exhibition Grounds

When: 22–25 September 2026

Find us: Hall 6.2 a, Stand 655

On the stand: Seppo Lindroth, Aki Norrbacka and Tom Bergström
Drop by the stand or book a time in advance and we will be ready for you.

Contact: Seppo Lindroth, Export Manager, seppo.lindroth@nordlift.fi



 


Lifting systems for rail vehicles

The typical job is raising a whole vehicle, a locomotive, a complete train, a tram or a metro car, straight off the rails, so the work underneath can begin. In bogie maintenance, our lifts raise the car body and allow the crew to roll the bogies out for service or replacement. On the production side, our column lifts are used in plants to build brand-new vehicles, lowering car bodies onto trolleys and handling the finishing stage at the end of the line.

InnoTrans matters to us because it brings the people who need exactly this into one place: rail operators, maintenance depots and vehicle manufacturers from around the world. It is where we can sit face-to-face and work out the right solution.

Every lift is built for the job

There is really no such thing as a standard lift for us. “It always depends on the workshop it goes into, the floor structure, where the lifting points are and how much the vehicle weighs. So, we build each one for the job,” says Aki Norrbacka, Chief Operating Officer at Nordlift.

The specifications come straight from the customer’s situation: the space, the vehicles being lifted and the process the lift must fit into. Current systems handle loads from 5 to 50 tonnes per column. We rarely start from a blank page, since years of rail projects mean there is usually a proven design to build from, but the result is always tailored to the real need.

Smooth, controlled and built to last

Our lifts are frequency-converter driven and logic-controlled, so every column rises together, evenly and under full control. While some competitors switch motors on and off with relays, and you feel every jolt, ours comes up smoothly. On loads measured in tens of tonnes, that steadiness is important. Safety standards set firm limits, and meeting them takes real design and engineering, which is where our experience shows.

They also last. “Honestly, they are almost too durable. We don’t get to sell many spare parts,” Norrbacka jokes. Some of the first lifts we built are still in daily service more than fifteen years on.

Maintenance is minimal, mostly just greasing the lifting screw, and the system monitors its own wear parts and alerts the operator when service is due.

Every lift ship with remote access is built in, so we can diagnose faults and fine-tune the controls from Finland without flying out for every small issue. Warranty is at least a year, often two, and we keep spare parts available long after delivery, well past the point where most equipment would be retired. This is what customers tell us they value most: dependable operation and a low lifecycle cost. You buy it once, run it for years and spend very little keeping it going.

Delivered and commissioned worldwide

“It doesn’t matter which country you’re from,” says Norrbacka. “If you have a real lifting need, come and talk to us and we will sort it out.”

We deliver worldwide, with recent projects shipped by the container load to sites across Europe and Asia. We also handle the installation, commissioning and operator training ourselves, on site, wherever the lift ends up. By the time we leave, your people know how to run it.

The muscle behind Nordlift

Nordlift is part of the same group as Veslatec, which gives us broad shoulders in both directions. We control the manufacturing chain from the front end, keep quality in check throughout production and can shorten lead times, which is often the deciding factor for an international customer working to a schedule. Communication stays straightforward and in-house, so there are less back-and-forth and fewer surprises. Customers who come to see how we work tend to notice the same thing: the quality and the capability are real.

Come talk about lifts in Berlin

Whether it’s a locomotive, a metro car, a tram or a lifting challenge nobody else will take on, we would like to hear about it. Come by our stand at InnoTrans 2026 or reach out to Seppo Lindroth in advance to book a slot, and we will make sure we are ready for you.

See you in Berlin.